PELATIHAN Rigging Lanjutan

TRAINING Rigging Lanjutan

PELATIHAN Rigging Lanjutan

Deskripsi PELATIHAN Rigging Lanjutan :

PELATIHAN Rigging LanjutanLifting Supervisor is in charge of the initial work of erecting the load and to ensure that all rigging work is carried out in a safe and efficient manner, adhering to the regulation and to sound established customs and practices.
The first consideration must at all times, be directed toward the safeguarding life and limb. This consideration must extend to all persons in vicinity or likely to enter the vicinity.

Tujuan PELATIHAN Rigging Lanjutan :

* Observe general safety first rules and carry out his duties in a safe and responsible manner.
* Have knowledge of safe working load of the crane he is working with.
* Have a full knowledge of hand signal (Australian/New Zealand Standard)
* Understand the correct type of sling, hook shackle etc. for load.
* Have knowledge of the use of lifting beams, slings and chains.
* Understand the effect of doubling crane hoist rope on safe working.
* Understand use of rope, chain and shackle.
* Understand not to use damaged wire rope or fiber rope, slings or chain where the links are not free or kinked wire rope.
* Understand when slinging a load, pack between sling and load at all point where load has sharp corners, so as to prevent damage to sling.
* Design and apply the knowledge of lifting and lifting plan in their daily work

Materi PELATIHAN Rigging Lanjutan :

Day 1:
1. Introduction:
2. Definition of Dogger, Slinging & Crane Operator
3. Roles & Responsibilities of Rigger:
4. Rigger Certification System
5. Roles & responsibility of Crane Operator
6. Roles & Responsibility of Dogger
7. Roles & Responsibility of Slinger
8. Roles & Responsibility of Traffic Controller / Flagman
9. Roles & Responsibility of Lifting Supervisor
10. Accident & Prevention
11. Legislative Requirement:
12. International Standard: AS/NZS
13. Roles and Responsibilities :Crane operator, Crane Owner/End User, Facility/Site Owner, Lift Coordination, Lift Engineer/ Rigging Specialist, Workers and Crane Mechanic
14. Hazard And General Safety:
15. Outriggers and Crane Stability
16. Comparative Soil Bearing Capacities
17. Crane Selection Guide
18. Electrical Hazard
19. Public Road / Pedestrian Hazards
20. Utilities Overhead and underground
21. Accidents and Lesson learn
22. Signalling And Communication:
23. Two way Radios
24. Conventional Radio
25. Trunked Radio
26. Radio Direction for Crane Driver
27. Bell or Whistle Code
28. Hand Signal

Day 2 :
1. Rigging Engineering Calculation
1. Determination on Centre of Gravity

* Rectangular Object
* Round or Oval Shape
* Multiple Load / Object

2. Rigging Engineering Calculation
3. Volume Calculation

* Rectangular Object
* Round or Oval Shape
* Triangle Object
* Cone Object
* Multiple Load / Object

Ropes & Knots for Rigger (Synthetic & Natural)
* Figure of Eight
* Reef knot
* Single Bowline
* End Splice
* Eye Splice
* Sheet Bend
* Timber Hitch
* Rolling Hitch
* 2 and Half Hitch
* Tagline Hitch
* Clove Hitch
* Etc

3. Rigging Engineering Calculation
4. Calculation of Mass

Basic Mass Calculation for Various Shapes of Loads Normally Engaged During Crane Operation versus volume
* Concrete / Cement
* Steel (Mild / Hard
* Liquid (Water)
* Wood
* Sand, etc

** Guidelines for Steel pipe, steel bar, Angle Bar, Mild Steel Plate, Mild steel plate bar, C-Channel, Universal Beams, Universal Columns, etc
1. Lifting Appliances

* Selection on Sling material
+ Sling wire FSWR 1570
+ Sling wire FSWR 1770
+ Chain Sling GT80 / G100
+ Synthetic Webbing (Flat/Round Slings)
* Stacking and Clearances
* Clearance
* Stacking Steel Plate
* Stacking Rolled Steel Coils And Other Round Loads
* Stacking Timber
* Care, Maintenance, and Inspection on Sling Material
* Spreader Bar vs Stabilizer Bar
* Use of Slings / Hoists And Tag line
* Determination of W.L (SWL versus WLL)
* Minimum Breaking Force (MBF) and its usages

Day 3:
1. Rigging Engineering Calculation

* Safety Factor requirements
* Lifting Material & Human
1. Sling wire FSWR 1570
2. Sling wire FSWR 1770
3. Chain Sling GT80 / G100
4. Synthetic Webbing (Flat/Round Slings)
* ‘choke’ / Hitch Factor

1. Rectangular Load
2. Round Load

* Sling Angles Factor

1. Sudut 30o
2. Sudut 45o
3. Sudut 60o
4. Sudut 90o
5. Sudut 120o

* Determination of sling Strength based on diameter & Safety Factor

1. Sling Wire
2. Synthetic Sling
3. Chain Sling

* Determination of Sling length and lifting angle

Day 4:
1. Rigging Engineering Calculation

* Inspection of Slings & shackles and attachments

1. Sling Wire (5%)
2. Chain Sling (5%)
3. Synthetic Sling

Note: Determination of acceptance condition of slings and attachments. (Category 1 and Category 2)
2. Rigging Engineering Calculation

* Calculation of Multiple Sling

1. SWL Sling 1
2. SWL Sling 2

* Multiple Crane Lifting / Multiple @ Large Loads

1. Tendem Lifting
2. Crane Selection and Ordering crane
3. Crane type vs Load Chart & Working Radius

* Mobile Crane
* Crawler Crane
* Role & Responsibility of Lifting Supervisor
* Designing Lifting Plan
* Special Lifting (Professional Engineer Interferences): Lifting Specialist in General

Day 5 :
1. Practical session on:
1. Determination of COG
2. Determination of Volume & Mass
3. Selection of slings
4. Lifting Techniques
5. Hand Signaling & Radio Communication
2. Inspection of Crane & Lifting Hoist appliances
3. Manual Lifting & Mechanical Lifting
4. Gin Wheel Application & Limitations

Day 6 :
1. ASSESSMENT PAPER :
2. General Knowledge
3. Assessment Legislation
4. Assessment Calculation (Lifting Plan)

Instructor

Michael Ferdinand Surjadi

Jadwal Pelatihan Jogja Media Training 2020 :

7-9 Januari 2020

4-6 Februari 2020

18-20 Februari 2020

3-5 Maret 2020

17-19 Maret 2020

14-16 April 2020

28-30 April 2020

12-14 Mei 2020

9-11 Juni 2020

23-25 Juni 2020

7-9  Juli 2020

21-23 Juli 2020

11-13  Agustus 2020

25-27 Agustus 2020

8-10 September 2020

22-24 September 2020

6-8 Oktober 2020

20-22 Oktober 2020

10-12 November 2020

24-26 November 2020

8-10 Desember 2020

28-30 Desember 2020

Catatan : Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta

Lokasi Pelatihan :

  • Yogyakarta, Hotel Dafam Malioboro
  • Jakarta, Hotel Amaris Tendean
  • Bandung, Hotel Golden Flower
  • Bali, Hotel Ibis Kuta

Investasi Pelatihan Tahun 2019 ini :

  • Investasi pelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta (on call). *Please feel free to contact us.
  • Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas Training :

  1. FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
  2. Module / Handout
  3. FREE Flashdisk
  4. Sertifikat
  5. FREE Bag or bagpackers (Tas Training)
  6. Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
  7. 2xCoffe Break & 1 Lunch, Dinner
  8. FREE Souvenir Exclusive
  9. Training room full AC and Multimedia

Jogja Training

Jogja Training adalah portal informasi training di yogyakarta.