PELATIHAN Pemeliharaan Listrik Tegangan Rendah dan Sedang

TRAINING Pemeliharaan Listrik Tegangan Rendah dan Sedang

PELATIHAN Pemeliharaan Listrik Tegangan Rendah dan Sedang

Deskripsi PELATIHAN Pemeliharaan Listrik Tegangan Rendah dan Sedang :

PELATIHAN Pemeliharaan Listrik Tegangan Rendah dan SedangThe backbone of many electric power systems is the medium voltage distribution system. Typically operating at voltages ranging from 2,400 to 34,500 Volts, voltage stress, corona, surges and protection of equipment all create unique challenges in design, equipment selection, operation and engineering. This 2 day class takes you through the basics of medium voltage power systems including components,equipment, design and operation problems as well as protection of medium voltage systems.

Tujuan PELATIHAN Pemeliharaan Listrik Tegangan Rendah dan Sedang :

Setelah selesai mengikuti kursus ini, peserta diharapkan akan mengerti dan memahami masalah Audit sampai pada penerapan konsep Power Management System. Dimana hal itu diperlukan oleh perusahaan sebagai suatu komponen pendukung kegiatan produksi untuk menjamin ketersediaan energi listrik dengan efisien dan murah.

Materi PELATIHAN Pemeliharaan Listrik Tegangan Rendah dan Sedang :

MEDIUM VOLTAGE SAFETY
* Electrocution at Low vs. Medium Voltage, Arc Flash,
* Qualified Person, Approach Boundaries

TYPES OF MEDIUM VOLTAGE SYSTEMS
* Utility and Industrial One lines, Reliability Requirements,
* Overhead and Underground Systems, Regulated Systems

MEDIUM VOLTAGE CABLE
* Copper vs. Aluminum Design, Voltage Ratings
* Insulation Ratings, 100%, 133%, 173% Insulation Levels,
* Shielding Requirements, Electric Fields, Terminating MV
* Conductors, Orientation of Overhead Lines

MEDIUM VOLTAGE SUBSTATION TRANSFORMERS
* Core and Coil Design, Aluminum and Copper Windings
* Tank Construction, Loss Evaluation, Efficiency, Regulation

SPOT NETWORKS
* Spot Network Design, Network Protectors, Network Protector
* Relay Operation, Directional Protection Requirements

PARTIAL DISCHARGE
* Corona, Surface Tracking, Voltage Stress, Sensing Partial
* Discharge, Component Failure

GROUNDING MEDIUM VOLTAGE SYSTEMS
* Resistance Grounding, Solid Grounding, Ungrounded Delta
* Charging Current, Effect of Ground Faults on Delta Voltage

SURGE PROTECTION
* Lightning and Switching Surges, Classes of Surge Arresters
* MCOV Ratings – (Maximum Continuous Operating Voltage)
* TOV – (Maximum Temporary Over Voltage Capability),
* Protective Characteristics, Surge Arrester Selection, Energy
* Capability, Effect of Grounding on Arrestor Selection,
* Insulation Coordination,

CURRENT TRANSFORMER APPLICATIONS
* Ratings, Selection Process, Accuracy, Saturation, Excitation
* Curves, Burden Calculation, Momentary Ratings

MEDIUM VOLTAGE CIRCUIT BREAKERS
* Vacuum, Air, Oil, SF6 Designs, Symmetrical Interrupting
* Rating, K-Rated Voltage Factor, Close and Latch Capability

RECLOSERS
* Application on Feeder Circuits, Recloser Settings
* Continuous Current and Interrupting Ratings

MEDIUM VOLTAGE FUSES
* Medium Voltage Switches, Load Rating, Close and Latch
* Rating, Short Time Rating, Expulsion vs. Current Limiting
* Fuse Characteristics, E and R Rated Fuses, Fuse Cutouts

MEDIUM VOLTAGE PROTECTION CONCEPTS
* Medium Voltage Protection, Relays, Circuit Breakers, R and
* E rated Fuses, Short Circuit vs. Overcurrent Protection

DISTRIBUTION FEEDER PROTECTION
* Protection with Fuses – 300%, Overcurrent Protection with
* Relays – 600%, Short Circuit Damage Characteristics, Relay
* “Reach” for End of Line Faults

ROTATING MACHINERY PROTECTION
* Requirements, Decrement Curves, Thermal Damage Curves,
* Reactive, Capability Curves, Differential Protection

MEDIUM VOLTAGE MOTOR CONTROLLERS
* Protection Requirements, Motor Management Relays, Circuit
* Breaker Protection, Relaying, Class R Rated Fuses

TRANSFORMER PROTECTION
* ANSI C57 Thru Fault Curves, Impact of Transformer Winding
* Configuration, Overview of Differential Protection, Inrush and
* Harmonic Restraint

Peserta Training Electrical Maintenance Low and Medium Voltage
* D3 atau SLTA yang berpengalaman kerja minimal 3 tahun, dan atau setara.
* Teknisi, Operator dan Supervisor didalam bidang instrumentasi, maintenance dan operasional.
* Mereka yang dalam tugasnya berhubungan dan atau terkait dengan materi kursus.

Metode PELATIHAN Pemeliharaan Listrik Tegangan Rendah dan Sedang :

Presentasi, diskusi, dan studi kasus.

Instructor

Tugino, ST.,MT dan Tim

Jadwal Training Tahun 2018 di Jogja Media Training :

  • 13-15 Februari 2018
  • 27-29 Maret 2018
  • 10-12 April 2018
  • 7-9 Mei 2018
  • 17-19 Juli 2018
  • 14-16 Agustus 2018
  • 18-20 September 2018
  • 16-18 Oktober 2018
  • 21-23 November 2018
  • 26-28 Desember 2018

Catatan : Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta.

Lokasi Pelatihan di Jogja Media Training :

  • Jakarta : Hotel Amaris Tendean (6.500.000 IDR / participant)
  • Yogyakarta : Hotel Dafam Malioboro (6.000.000 IDR / participant)
  • Bandung : Hotel Golden Flower (6.500.000 IDR / participant)
  • Bali : Hotel Ibis Kuta (7.500.000 IDR / participant)
  • Lombok : Hotel Jayakarta(7.500.000 IDR / participant)

Investasi Pelatihan tahun 2018 ini :

  1. Investasi pelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta (on call).
  2. Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Catatan : Apabila perusahaan membutuhkan paket In House Training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas Training di Jogja Media Training :

  1. FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
  2. FREE Akomodasi Peserta ke tempat pelatihan .
  3. Module / Handout
  4. FREE Flashdisk
  5. Sertifikat
  6. FREE Bag or bagpackers (Tas Training)
  7. Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
  8. 2xCoffe Break & 1 Lunch, Dinner
  9. FREE Souvenir Exclusive
  10. Training room full AC and Multimedia

Jogja Training

Jogja Training adalah portal informasi training di yogyakarta.